Cookie settings

Choose what we may use beyond the necessary cookies. You can change this any time from Cookie settings at the bottom of every page.

EN
Shop
Find your kit
Find your kit

Articulator · Flex

DACOS Omni for ASA Dental 5032

Use DACOS Omni Flex on your ASA Dental 5032 articulator: bond the plates once, then mount every model magnetically. Flex covers the ASA Dental 5032.

See the recommended kit
Illustration: ASA Dental 5032 articulator with DACOS Omni Flex and the calibrator mounted between its members

How DACOS Omni fits your ASA Dental 5032

Models covered
ASA Dental 5032
Fit
FlexFlex: the plates are bonded once with plaster on the articulator’s mounting plates, then every model mounts by magnets.
Installation
Plaster the two Flex plates once on the articulator’s own mounting plates. From then on the models seat on the plates by magnets, with no more plaster for the models. Then run the TrueZero™ calibration once on that articulator: the pin returns to zero.

Recommended kit

Pick the height for your cases: Light for no implants or implants on one arch, Ultra for implants on both arches, Duo for both heights in one box.

Full kit details

DACOS Omni Flex

Choose your height
Duo (35 + 55 mm)Most chosenBoth heights, one boxUSD 366.60Light (35 mm)Crowns, bridges, veneers, orthoUSD 197.40Ultra (55 mm)Implants, All-on-X, multiple analogsUSD 197.40

Both heights on the bench: Light for daily work, Ultra for implant cases. USD 28.20 less than two single kits.

One height is enough? Light or Ultra alone costs USD 169.20 less.

USD 366.60

Prices shown without VAT. Prices in USD. Taxes and duties are shown at checkout.

Dispatched from Italy within 2 business days

  • Secure checkoutShop PayApple PayGoogle PayVisaMastercardMaestroPayPal
  • Invoice with every order

What’s inside the DACOS Omni Flex

Duration 1:23

Installation, step by step

How it goes on

Once per articulator: the plates are plastered on with the calibrator between them. Then every model mounts by magnets.

The photos show Flex on two different articulators. On yours the steps are the same.

  1. The two printed halves of the TrueZero calibrator on the build platform, still on their supports

    Print the calibrator

    Print the two halves of the TrueZero™ calibrator on your own printer, with the same resin, settings and post-curing as your models. The fitting test before it picks the offset.

  2. Gloved hands holding the calibrator block between the Flex plates marked UPPER and LOWER

    Seat the plates on the block

    Join the calibrator halves into one rigid block. Seat the UPPER plate on the upper half and the LOWER plate on the lower half, and never swap them.

  3. Articulator front view with the incisal pin at zero and an elastic band stretched around it

    Set the incisal pin at zero

    Mount your articulator’s own split cast mounting plates, upper and lower. Set the incisal pin at zero and lock it.

  4. Calibrator block with Flex plates centred between the articulator members on the elastic band

    Centre on the elastic band

    An elastic band around the articulator marks the Bonwill triangle. Centre the block between the members and line up its occlusal plane with the band.

  5. Plaster applied on the upper Flex plate under the articulator upper member

    Plaster the upper plate

    A little silicone under the LOWER plate holds the block steady. Close the articulator, pin at zero, and plaster the UPPER plate to the upper mounting plate.

  6. Articulator closed on the calibrator with both Flex plates plastered

    Then the lower, and let it set

    Take out the silicone and plaster the LOWER plate the same way. Keep the articulator closed until the plaster has fully set.

  7. Flex upper and lower plates installed on the articulator with free space between them

    Take out the calibrator

    Both plates are installed. From here on models mount by magnets, with no more plaster and no recalibration.

What labs say

  • In the spotlight

    Ricky Huang

    Prosthodontics Resident at Harvard School of Dental Medicine

    United States

    Brilliant design with strong customization (nine site options for different cases) and the mounting calibration, which should improve accuracy!

  • Jorge Valladares

    Ceramist dental technician · 360 Estudio Dental

    Mexico

    A predictable, practical, clean, and simple-to-use work system.

    Ceramic crowns on a printed model mounted on a red DACOS Omni plate
    Case photo shared by Jorge Valladares

  • Giancarlo Stabile

    Dental technician

    Italy

    I was truly shocked: a milled provisional seated on the model, and everything lines up.

    Two ASA Dental articulators with red DACOS Omni plates
    Case photo shared by Giancarlo Stabile

  • Martynas

    Dental technician

    Lithuania

    the least questionable system available on the market.

  • Simone Fedi

    Dental technician

    Italy

    I've finally found a simple, effective system for printing models through the Model Creator module in Exocad, with a beautiful and extremely precise design. The models are lightweight and reduce resin consumption. They don't have bulky or outdated bases, and I don't have to change anything in my workflow — I can keep printing horizontally, with the added flexibility of managing the model base and the digital analogs. Fully approved!

    Full arch models on black DACOS Omni Ultra plates in the articulator
    Case photo shared by Simone Fedi

  • Andrea Pugno

    Dental technician · Pugnolab

    Italy

    In our CAD workflow, design is only half the job. We were looking for a system that would let us take a real step up in the manual verification of our projects, especially for tasks requiring a highly dynamic approach, such as checking a 3D-printed bite splint. With the new Dacos Omni, we found exactly what we needed. Thank you, Antonello

    Printed splint on a red DACOS Omni plate
    Case photo shared by Andrea Pugno
Read all reviews

Questions about ASA Dental 5032

Why not the ASA Dental kit?

The ASA Dental direct kit fits the 5010, 5050 and 5050Plus only. The 5032 takes Flex: the plates are plastered once on its mounting plates, then every model mounts by magnets.

Do I still plaster models?

Only the two Flex plates are plastered, once, during the installation. The printed models seat on the plates by magnets.

What happens after the installation?

You run the TrueZero™ calibration once on that articulator. The calibration belongs to the articulator the plates are installed on, so the plates stay on it.

More than one articulator?

Each articulator gets its own set of plates, calibrated on that articulator. Flex Plates cover one more articulator in the lab with the same magnetic workflow.

See Flex Plates

Italian business with a Partita IVA? Buy without Italian VAT (reverse charge, art. 17(2) DPR 633/72).Continue in Italian

All articulators

Your cart

Find your kit